Home > Pool Lifts > Aquatic Access Pool & Spa Lifts
Choose a sub category:
Aquatic Access Pool & Spa Lifts
Sort By:
Page of 1
MODEL AG48 Above Ground Lift MODEL AG48 Above Ground Lift (Not ADA Approved)

Aquatic Access manufactures a variety of AG (Above-Ground) lifts, each of which is configured to fit the pool or spa where it is to be used (not ADA approved, but great for home use!). The length of the lift’s cylinder governs the distance the seat travels vertically to clear the wall of an above-ground pool/spa. The AG-48 has a 31” vertical seat travel; the AG-60 has a 42” vertical seat travel; and the AG-72 has a 51” vertical seat travel and is designed for high-wall therapy tubs as shown.


These lifts mount on a 16” plate with a supportive tripod ( for freestanding applications) which is bolted to the deck, or a smaller plate coupled with a top wall bracket attached to the top flange of the pool. The AG lifts can also be designed as WP models to mount on a customer-supplied 6” x 6” wood post which is usually set in concrete a minimum of 30” deep. Seats on all of the AG lifts can be forward-facing (cylinder behind) or side-facing (cylinder on left or right of seat). Forward-facing seats allow user’s legs and feet to clear benches in pools/spas. Pricing below is for standard models

AG48WP Above Ground Lift w/Wood Post AG48WP Above Ground Lift w/Wood Post (not ADA Approved)

Aquatic Access manufactures a variety of AG (Above-Ground) lifts, each of which is configured to fit the pool or spa where it is to be used. The length of the lift’s cylinder governs the distance the seat travels vertically to clear the wall of an above-ground pool/spa. The AG-48 has a 31” vertical seat travel; the AG-60 has a 42” vertical seat travel; and the AG-72 has a 51” vertical seat travel and is designed for high-wall therapy tubs as shown.


These lifts mount on a 16” plate with a supportive tripod ( for freestanding applications) which is bolted to the deck, or a smaller plate coupled with a top wall bracket attached to the top flange of the pool. The AG lifts can also be designed as WP models to mount on a customer-supplied 6” x 6” wood post which is usually set in concrete a minimum of 30” deep. Seats on all of the AG lifts can be forward-facing (cylinder behind) or side-facing (cylinder on left or right of seat). Forward-facing seats allow user’s legs and feet to clear benches in pools/spas.

MODEL IGRC In-Ground Recessed Cylinder MODEL IGRC In-Ground Recessed Cylinder (Not ADA approved)

The Model IGRC is a good choice for pools with automatic covers and moveable floors, in-ground spas with bench seats, and pool/spa combinations. It has a low profile with the cylinder recessed into either a 6" or 8" PVC (customer-furnished) sleeve in the deck. This model can be built into wood decks or raised walls. Call 1-800-634-4351 for more information and a free DVD or CD-ROM. Please provide dimensional information about your pool on our Dimensional Worksheet.


Optional side seats and several styles of self-turn handles allow some people to be able to use this lift unassisted by manually rotating themselves while on the seat.

MODEL IGMT Manual Turn Lift MODEL IGMT Manual Turn Lift (not ADA approved)

The IGMT is a good choice for pools with automatic covers and moveable floors, for in-ground spas with bench seats, and for pool/spa combinations. The Model IGMT has no parts in the water except when the seat descends. The 360º seat turn allows good access from anywhere on the deck.


The IGMT is available with three seat configurations -- pictured is the Front--Facing Seat -- a good choice for in-ground spas and pool combinations and spas with seats. The Left-Mounted and Right Mounted Seats are choices available for in-ground pools. Specify seat configuration when ordering.

AG60WP Above Ground Lift w/Wood Post AG60WP Above Ground Lift w/Wood Post (not ADA approved)

Aquatic Access manufactures a variety of AG (Above-Ground) lifts, each of which is configured to fit the pool or spa where it is to be used (not ADA approved, but great for use at home). The length of the lift’s cylinder governs the distance the seat travels vertically to clear the wall of an above-ground pool/spa. The AG-48 has a 31” vertical seat travel; the AG-60 has a 42” vertical seat travel; and the AG-72 has a 51” vertical seat travel and is designed for high-wall therapy tubs as shown.


These lifts mount on a 16” plate with a supportive tripod ( for freestanding applications) which is bolted to the deck, or a smaller plate coupled with a top wall bracket attached to the top flange of the pool. The AG lifts can also be designed as WP models to mount on a customer-supplied 6” x 6” wood post which is usually set in concrete a minimum of 30” deep. Seats on all of the AG lifts can be forward-facing (cylinder behind) or side-facing (cylinder on left or right of seat). Forward-facing seats allow user’s legs and feet to clear benches in pools/spas.

AG60 Above Ground Lift AG60 Above Ground Lift (not ADA approved)

Aquatic Access manufactures a variety of AG (Above-Ground) lifts, each of which is configured to fit the pool or spa where it is to be used. The length of the lift’s cylinder governs the distance the seat travels vertically to clear the wall of an above-ground pool/spa. The AG-48 has a 31” vertical seat travel; the AG-60 has a 42” vertical seat travel; and the AG-72 has a 51” vertical seat travel and is designed for high-wall therapy tubs as shown.


These lifts mount on a 16” plate with a supportive tripod ( for freestanding applications) which is bolted to the deck, or a smaller plate coupled with a top wall bracket attached to the top flange of the pool. The AG lifts can also be designed as WP models to mount on a customer-supplied 6” x 6” wood post which is usually set in concrete a minimum of 30” deep. Seats on all of the AG lifts can be forward-facing (cylinder behind) or side-facing (cylinder on left or right of seat). Forward-facing seats allow user’s legs and feet to clear benches in pools/spas.

AG72 Above Ground Lift AG72 Above Ground Lift (Not ADA approved)

Above-Ground Lift for pool walls around 60" high


The Pool Lift Model AG72 was specifically designed to lift people into and out of above-ground high wall therapy pools. After raising the seat, the therapist turns the seat while helping to lift the patient's legs, then turns the valve handle to lower the seat inside the pool. The stainless-steel plate at the base of the cylinder is bolted to the floor, and a stainless-steel bracket around the top of the cylinder is bolted through the top pool flange. The standard seat has two arms and a seat belt is included with each lift. Refer to the our dimensional worksheet for the measurements we need to know before building this model lift for you. Please call or email us and wee will send you the worksheet.

IGAT-180 InGround Pool Lift W/180 Degree Turn

ADA-Compliant Lifts for In-Ground Pools/Spas IGAT-180 models meet or exceed the Americans with Disabilities Act requirements for pool lifts.

The ADA requires independent operation and easy seat retrieval from deck or water. Upper and lower controls make this easy with Aquatic Access products. There is no need to lean over and reel in a single control box which may be on the seat in the water. Lifts are powered by city water pressure from a hose connection or plumbed-in line. Installation requires only anchor socket placement in deck. Pool edge sketch/dimensions required.

• Price includes concrete anchor!
• Install at min. 36" straight wall
• Lifts approx. 400 lbs. at 55-60 PSI operating pressure, depending on weight of optional accessories
• Portable - Lifts out and rolls away with no tools
• Weighs only 82 lbs.
• Standard lift height in raised position -- 73"
• The IGAT-180 is compact, lightweight, and easy to remove and replace with no tools.
• No underwater installation.
• Bottom of cylinder touches pool wall. Vinyl-liner wall pad is available.
• Independent Operation
• Water Pressure Powered
• Adjustable Seat Height
• No Electricity or Battery Needed
• Remove with No Tools

The IGAT-180 models allow maximum access from the deck for the user and any assistant. Side-to-side transfers are easy- the footrest flips up and the mounting arm is under the seat, allowing wheelchair access and unobstructed transfer. On a standard installation, seats automatically rotate forward (clockwise) into pool/spa, travel 42" vertically, can be stopped or reversed at any point, and can be padlocked in the raised position with the water turned off. Pool edge sketch/dimensions required.

INCLUDED: A stationary cylinder-side armrest, flip-up footrest, deck socket and socket cover.

IGAT-180/135 InGround Pool Lift  W/180 Degree Turn IGAT-180/135 InGround Pool Lift W/180 Degree Turn

Price includes Concrete Anchor, $189 value!

Aquatic Access Model IGAT-180/135
In-Ground, Automatic 135° Seat Turn
For Pools/Spas With Benches

Automatic135° Seat Turn Avoids Benches
Portable - Lifts out and rolls away with no tools
Lifts approx. 400 lbs. at 55-60 PSI operating pressure, depending on weight of optional accessories

Model IGAT-180/135 allows the user's feet on footrest to miss built-in benches and descend in deeper center of pool/spa. Rubber pad under seat protects bench.

Meets the 2010 Standards for Accessible Design (ADA regulations).

- Automatic 135° clockwise seat turn.

- Lifts 400 lbs. at 55-65 PSI, depending on weight of accessories chosen.

- Portable - lifts out and rolls away with no tools.

- Height of the lift in raised position varies up to 7'1".

- Model IGAT-180/135 allows the user's feet on the footrest to avoid built-in benches and descends into the deeper center of the pool/spa.

A rubber pad under the seat is available to protect bench.

- Standard unit rotates clockwise; opposite turn (opposite facing seat) is available.

IGAT-180/135 InGround Pool Lift  W/180 Degree Turn IGAT-180/AD InGround Pool Lift Above Deck

Previously available as a custom design, the Model IGAT-180AD is designed to accomodate pools with automatic covers and some pool/spa combinations. This lift complies with the 2010 Standards for Accessible Design, the current requirements of the Americans with Disabilities Act (ADA). It is user-operable, and its seat height is easily adjustable to accommodate various wheelchair heights. The 180° clockwise turn allows the greatest access from the deck for the user and any assistants. Side-to-side transfers are easy, the footrest flips up and the mounting arm is under the seat. This allows for unobstructed transfer. The seat rotates forward when entering the pool, and backward when exiting the water. The standard seat has a right arm only, but a flip-up outer arm is available. This unit also available in a 90-degree and 135-degree rotation. Just let us know your needs when ordering. We strive to make our lifts fit your needs. When you call to order, please let us know about your pool cover and/or adjacent spa. Refer to the Aquatic Access Dimensional Worksheet to determine what information we need to build this unit. You can download this form in .pdf format, fill the information required for your installation, and return the form to us with your order.


*Static pressure (measured at faucet or hose with no water flowing) is affected by variables in the material, length, diameter, and rigidity of the water lines and hoses from the street to the lift, and by how many other faucets are open at the same time. Operating pressure requirement (measured while lifting) is not affected by these variables.

** Opposite facing (opposite turn) units available (custom charges may apply).